L.U.C.A.S SMART Manual 1.0
4 Operating the System
If you decide to start ECP from the NO-SOD Center, type your username and paswword, select the ECP module and click on the ENTER button. If your username and password are the good ones, the ECP web interface should be displayed. From now, you can start using ECP and create/modfy users or manage groups for all your installed NO-SOD modules. MPEGIOPro User Manual Page 3 Version 1.0.4 4. Hardware Installation Un-plug the PC’s power cable, open PC case, locate a free PCI slot, plug in the MPEGIOPro card and screw it firmly to the back-panel. MPEGIOPro User Manual Page 7 Version 1.0.4 then follow the on-screen instructions to install the application software. Un-installing the MPEGIOPro application software can be done from Windows’ Control-Panel.
First, make sure the Power On switch is set to the
Off position.
Caution! Connect the power cable only after you
have made absolutely sure that the local mains
voltage matches the voltage specified on the device.
If you connect the system to the wrong mains voltage,
you can easily damage the electronic components of
the L.U.C.A.S SMART system.
Gain Line In, Aux In, Mic In
Turn all Gain knobs (Gain Line, Gain Mic and Gain
Aux) all the way down (counterclockwise as far as
they will-go).
Before you power L.U.C.A.S SMART up, make sure
that all connected peripheral components are
switched on first. Your mixer, and all signal sources
connected to it such as keyboards, instrument amps,
effects and so forth, should be switched on-first.
The L.U.C.A.S SMART system should always be swit-
ched on last. Again, that means after you switch on
all connected devices. After you power the system up
by activating the On/Off switch (it will light up red
when it is set to On and getting mains power),
set the Gain Line knob to the center or 12 o’clock
position (= 0 dBV).
This is the preferred level if you have connected
a mixer to L.U.C.A.S SMART. If you connect a CD
player or a keyboard directly to the system, turn the
Gain Line knob clockwise all the way to the far right
to achieve maximum volume.
Mb748ll 1.0.4 User Manual Pdf
Note: Many DJ mixing desks are equipped with RCA-
format outputs only. If you want to employ this type
of mixer, use either an RCA/XLR adapter (or RCA/1/4'
jack adapter) and plug it into the Line In port,
or connect the mixer to Aux In using a standard
RCA connector-equipped cord.
If you want to plug a CD player directly into the sys-
tem, use Aux In to do this. Depending on signal
level, you can turn the Gain Aux knob all the way to
the right in order to achieve maximum volume.
5 Settings
Gain Mic Knob
Use this knob to adjust microphone level.
Note: You can adjust the microphone and line inputs
separately and mix them as desired. In the event of
audible distortion or saturated signals, back off the
Gain Mic knob.
Gain Line Knob
If you hear distortion or saturated signals, first check
the signal sources and, if possible, reduce the output
signal level there. If the signal that you are routing
to the L.U.C.A.S SMART system cannot be adjusted
at the source, adjust the power amp by backing off
the Gain Line knob.
Gain Aux Knob
Use this knob to adjust the level of the Aux In channel.
Note: You can adjust Aux In and Line In separately
and mix them as desired. In the event of audible
distortion or saturated signals, back off the
Gain Aux knob.
Mode
If you have just a mono signal available, patch it to
the left input of the Line In or Aux In circuits. Set
the Mode switch to Mono. This way the system can
output the monaural input signal on both left and
right sides.
User Manual Pdf
Balance
Use the Balance knob to adjust the relative levels of
the left and right channels. The two sides’ volume
levels are equal when the knob is set to the center
position.
Subwoofer Level
When this knob is set to the center position, the
volume of the subwoofer is perfectly balanced with
the levels of the satellites so that the audience
is treated to a homogeneous sound with an even
distribution of bottom-end and top-end (satellite)
signals. If you want to boost or cut the bass frequen-
cies, simply turn the Subwoofer Level knob to the
left (down to -12 dB) or right (up to +6 dB).
Instruction Manual
Comments are closed.